Artikelnummer:
BMM20400

BMM20400 B&M TORK MASTER 2000 TH400/350 1800-2200 RPM stall

3 195 kr
Finns i lager
Finns ej i lagret
.
  Köp »
Finns ej i lagret
Produktbeskrivning:
TORK MASTER 2000 TH400/350 1800-2200 RPM stall
10.75-inch bolt circle, 1800-2200 RPM stall
This Tork Master 2000 fits 1965-91 GM TH400, 425, 375 and 1968-81 GM TH350, 375B (not 350C.) Don't let the exceptional value fool you into thinking Tork Master Converters are not packed with lots of quality features which make them the best value-priced street performance converters money can buy. These converters perform best when paired with stock to modified engines up to 350hp/350 ft lbs of torque, and lighter weight applications, like street rods. The Tork Master will provide noticeably quicker launches and harder acceleration while maintaining normal daily driving qualities. Upgrades like a new precision alloy steel pump drive tube, needle thrust bearing when factory equipped, new thrust washer between turbine and cover when required, and pressure tested and fully balanced by expertly trained technicians. Notes: Higher stall converters can generate more heat, so we highly recommend adding a transmission cooler. Notes: Not recommended for big block, supercharged, plate-type nitrous oxide or trans-brake applications. The product images shown are for illustration purposes only and may not be an exact representation of the product. Has 10.75-inch bolt circle

Quicker Launches and Harder Accelaration
New Precision Alloy Steel Pump Tube
Fully Balanced and Pressure Tested
B&M Quality & Durability

Frequently Asked Questions
WHAT SHOULD I EXPECT FROM A PERFORMANCE TORQUE CONVERTER?
Strength and durability is an additional benefit if the converter is properly engineered. Furnace brazing is used to strengthen the converter internally for high performance, racing and heavy-duty applications.
WHAT IS STALL SPEED?
Stall speed numbers are listed primarily to rate the converter’s performance level. Typically, the number assigned, 2000, 2400, 3000 etc, lets you know what to expect from the converter. If a 2400 is selected, you should be able to flash stall the converter to about 2400 RPM. This should provide anywhere from 500 to 1000 more RPM to launch, or accelerate, the vehicle from a dead stop, as compared to the stock converter in the vehicle. This increase should substantially improve the acceleration capability of the vehicle. Lighter cars, 2800 lbs and under, typically stalls a little lower than the above mentioned numbers, therefore you should choose a converter with a higher stall number for optimum performance.
HOW DOES THE ENGINE’S CAMSHAFT AFFECT THE TORQUE CONVERTER’S PERFORMANCE?
The camshaft will affect the torque curve of the engine, which will affect the performance of the converter. For example if your 350 CID engine produces 230 lb.ft. of torque at 2400 rpm, a B&M HoleShot 2000 Converter will produce 2000 rpm stall speed. If you install a 268-degree cam into this engine you will raise the torque curve and at 2400 rpm your engine will produce less torque. Thus the 2000 stall converter will only stall at 1800 or less. However with this new cam the engine will make much more power above 3000 rpm. Keep in mind when the torque curve of the engine is raised you will need more stall speed in the converter to allow the vehicle to accelerate at low rpm (below 3000). A good rule of thumb for advertised cam durations up to 248 degrees, a 2000 or 2400 stall converter is a good choice. Advertised cam durations up to 268 degrees, a 2400 or 3000 stall converter is a good choice. Advertised cam durations over 272 degrees, a 3000 to 3600 stall converter is a must.